Separating Ethanol From Water

Separating Ethanol From Water Via Differential Solubility -- using sulfur
Separating Ethanol From Water Via Differential Miscibility -- using castor oil

Separating Ethanol From Water Via Differential Solubility

Alcohol for combustion could be purified more economically

Langley Research Center, Hampton, Virginia


THE differential solubility of sulfur in ethanol and water could be exploited to separate ethanol from water. The energy that could be produced by burning the separated ethanol would be more than that required in the separation process. In contrast, the separation of a small amount of ethanol (actually an ethanol/water solution poor in ethanol) from water by distillation requires more energy than can be produced by burning the resulting distillate. The proposed alcohol/water separation process could be exploited industrially to produce clean fuel from fermented vegetable matter.

In one version of this concept, sulfur would be added to an ethanol/water mixture: a slight amount of sulfur that depends on the temperature of the mixture would be dissolved by the ethanol. (All three forms of sulfur are insoluble in water, even at its boiling temperature, but the a form of sulfur is slightly soluble in ethanol and the b form is more soluble in ethanol, according to the CRC Handbook of Chemistry and Physics.) The sulfur/ethanol mixture would settle to the bottom of the container, where it could be bled off. This small part of the original mixture could then be heated to separate the volatile ethanol from the significantly less volatile sulfur. The hot sulfur left after the distillation could be added to another batch of the ethanol/water mixture.

In comparison with the energy consumed in the conventional distillation process, a significant amount of energy would be saved in this process because only the small bled-off portion of the original mixture would have to be heated. Because of its solubility in ethanol, the b form of sulfur would be used when the separation process was carried out at room temperature and atmospheric pressure. Finely divided sulfur that was not dissolved by the ethanol would float on the mixture.

In an alternative version of this concept, the ethanol/water/sulfur mixture would be placed in a retort, where it could be heated and pressurized to a temperature above the critical temperature and pressure of ethanol [243 deg C and 63 atm (6.4 MPa), respectively] but below the critical temperature and pressure of water [374.1 deg C and 218.3 atm (22.12 MPa), respectively]. The mixture would be retorted at a temperature slightly above 243 deg C and at a pressure slightly above 63 atm (6.4 MPa), putting the ethanol in the supercritical state, in which it should easily dissolve all three forms of sulfur (including the form which is insoluble at ambient temperature and pressure). The water, on the other hand, would still be well below its critical state and still should not dissolve sulfur. The sulfur/ethanol mixture would settle to the bottom of the retort, where it could be piped away under pressure and at high temperature. The sulfur/ethanol mixture would then be expanded to a lower temperature and pressure at which not as much sulfur could be dissolved in the ethanol and at which ethanol would partially separate from the mixture.

Further heating of the remaining mixture at a pressure of 1 atm (0.1 MPa) would separate most of the remaining ethanol and sulfur. The sulfur could be reused, and the high-pressure hot water could be used to cook more mash to be fermented or to preheat a charge going to another retort. This second version is probably the most suitable for an industrial process, and could be aided by the addition of a centrifuge to separate the initial two-phase mixture. The role of sulfur in both versions could be played by another substance. However, the low toxicity and very low vapor pressure of sulfur at the boiling temperature of ethanol appear to make it the best candidate.

This work was done by Renaldo V. Jenkins of Langley Research Center. No further documentation is available. LAR-14894

Separating Ethanol From Water Via Differential Miscibility

The differential miscibility of castor oil in ethanol and water would be exploited to separate ethanol from water, according to a proposal. Burning the separated ethanol would produce more energy than would be consumed in the separation process. In contrast, the separation of a small amount of ethanol (actually an ethanol/water solution poor in ethanol) from water by the conventional process of distillation requires more energy than can be produced by burning the resulting distillate. As in the process described in the preceding article, "Separating Ethanol From Water Via Differential Solubility" (LAR-14894), the proposed alcohol/water separation process could be exploited industrially to produce clean fuel from fermented vegetable matter.

In one version of this process, castor oil would be added to an ethanol/water solution. The ethanol would mix freely with castor oil, which is insoluble in water. The resulting ethanol/castor-oil phase, which would contain less than 1 percent water, would collect as the top layer, the bottom layer being the remainder of the ethanol/water solution somewhat depleted in ethanol. Heating this two-layer mixture to a temperature slightly below the boiling temperature of ethanol (78.5 deg C) would cause the partial pressure of ethanol above the top layer to be much greater than the partial pressure of either castor oil or water. This vapor-phase ethanol could be condensed in a relatively pure state.

Although heating an isolated ethanol/water solution like that in the bottom layer would normally raise the vapor pressure of both ethanol and water above the solution, this would not be the case in the presence of the top castor-oil/ethanol layer for the following reasons: The amount of water that could dissolve in the top castor-oil/ethanol layer would increase only slightly upon heating. On the other hand, ethanol could readily cross the interface between the two layers and enter the top layer. As long as the total mix was kept at a temperature below the boiling temperature of ethanol (thereby preventing agitation of the layers by boiling), the diffusion of water through the castor-oil/ethanol phase would be inhibited.

In an alternative version of this concept, the upper castor-oil/ethanol layer would be skimmed off and heated to obtain the ethanol. Once the ethanol was driven off, the castor oil could be returned to an ethanol/water solution to dissolve more ethanol to repeat the process. This concept could readily lend itself to a continuous process. Substances other than castor oil (one of its components perhaps, or another substance) could be used in this process or to extract other compounds from other mixtures by using this upper-of-two-phases vaporization technique.

This work was done by Renaldo V. Jenkins of Langley Research Center. No further documentation is available. LAR-14895


Back to Biofuels Library


Biofuels
Biofuels Library
Biofuels supplies and suppliers

Biodiesel
Make your own biodiesel
Mike Pelly's recipe
Two-stage biodiesel process
FOOLPROOF biodiesel process
Biodiesel processors
Biodiesel in Hong Kong
Nitrogen Oxide emissions
Glycerine
Biodiesel resources on the Web
Do diesels have a future?
Vegetable oil yields and characteristics
Washing
Biodiesel and your vehicle
Food or fuel?
Straight vegetable oil as diesel fuel

Ethanol
Ethanol resources on the Web
Is ethanol energy-efficient?


Community development | Rural development
City farms | Organic gardening | Composting | Small farms | Biofuel | Solar box cookers
Trees, soil and water | Seeds of the world | Appropriate technology | Project vehicles

Home | What people are saying about us | About Handmade Projects 
Projects | Internet | Schools projects | Sitemap | Site Search | Donations | Contact us